Showing posts with label installation. Show all posts
Showing posts with label installation. Show all posts

Friday, May 17, 2013

2003 HONDA ACCORD 2 DOOR FRONT UNDER SPOILER INSTALLATION MANUAL

PARTS LIST : Front under spoiler, 3 Rounded clip nuts, 2 Square clip nuts, 4 Washer-screws, 4 Spring nuts, 5 Flange bolts.
TOOLS AND SUPPLIES REQUIRED : Phillips screwdriver, Flat-tip screwdriver, Ratchet, 10 mm Socket, Masking tape, Isopropyl alcohol, Shop towel.

INSTALLATION INSTRUCTIONS :
NOTE: Be careful not to damage the front bumper and the body paint finish. This front under spoiler kit should be installed only if the ambient air temperature is 60°F (15°C) or above. To allow the adhesive to "cure", do not wash the car for 24 hours.
1. Remove the four bolts that fasten the bumper weight to the front bumper, and remove the bumper weight through the bumper grille.
2. Remove the two clips and two washer-bolts from the front bumper.
3. Slide the four spring nuts (two on each side) over the holes in the front bumper. Slide the three rounded clip nuts onto the bottom flange of the front bumper through the cutouts. Slide the two square clip nuts onto the opening of the front inner fender. Note the direction of the clip nuts.
4. Attach a strip of masking tape to the ends of the seven adhesive backings, and remove 40 to 50 mm of adhesive backing. Fold the ends back, and tape the ends to the front of the front under spoiler.
5. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the front under spoiler will attach.
6. Position the front under spoiler on the front bumper, and install the five flange bolts and two washer-bolts removed in step 1.
7. Starting in the center, work your way around the side. Hold light pressure on the front under spoiler, and carefully remove the adhesive backings from the front under spoiler in the direction shown. Using the palm of your hand, hold the front under spoiler firmly against the front bumper for 30 seconds.
8. While holding the front under spoiler against the bumper, install the two washer-screws on each side.

download for full details click here
Read more »
Posted by at
Labels: , , , , , , , , ,

Monday, May 13, 2013

Honda Civic Radio Replacement Installation Removal Manual

INSTALLATION / REMOVAL INSTRUCTIONS :
NOTE : Removing the radio in this vehicle requires removing lower dash panels on both the drivers and passenger sides of the vehicle as well as the center console panel as seen in the photo above. Once this center console panel is removed, you will access to the hidden screws that secure the radio to the dash.
STEP 1 : Locate and remove (2) phillips screws on the curved lower dash panel below the radio. The 2 screws will be located above the cigarette lighter plug.
STEP 2 : Open the glove box. There are two (2) hidden screws that need to be removed. The first screw is located at the top left corner of the glove box assembly. Locate and remove one (1) brass colored phillips screw . Remove Factory Radio
STEP 3 : The glove box must be freed from the dash. To keep the glove box from falling to the floor of the vehicle, stop bumpers are attached to each side of the glove box. With you hand, firmly push in the thin plastic of the glove box. You will see the stop bumper attached to the side of the glove box. If you push in hard enough, you can free the stop bumper from behind the dash. Do this to each side, one side at a time, and the glove box will fall free of the dash panel.
STEP 4 : The second hidden screw is located at the lower left corner of the glove box and can only be accessed when the glove box is completely lowered out of the dash. This screw is a phillips screw as well as an 10 mm bolt. Remove this screw/bolt.
STEP 5 : You will need to remove the lower left dash panel below the steering column. This panel is secured to the main dash with three (3) phillips screws . Remove all 3 phillips screws.
STEP 6 : Once all 3 phillips screws have been remove, the lower dash panel can be pulled from the main dash. The top of the lower dash panel is secured to the main dash with one snap on the left of the steering column, and one snap on the right of the steering column. Gently pull to unsnap and free the lower dash panel from the main dash. Mount New Radio Wire New Radio Cover Page Before You Begin Remove & Install
STEP 7 : Once the lower left dash panel has been removed, you will be able to see a brass colored screw that had been hidden behind the top right of the dash panel just removed (to the right of the steering column). Locate and remove one (1) phillips screw.
STEP 8 : All hidden screws securing the lower center dash panel have been removed. With your hands, pull the right side of the lower dash panel (the part of the panel secured by 2 screws hidden behind the glove box) then pull the left side. You will have to wiggle the panel but should be able to pull the panel away from the main dash. Unplug the connector attached to the rear of the cigarette lighter attached to the lower dash panel.
STEP 9 : The radio is secured to the dash with two (2) 8 mm screws / phillips screws at the rear of the radio. The only way to remove these screws is to look up, under the radio where the center dash panel was just removed. Locate and remove both screws. Once the screws have been removed, pull the radio out of the dash.
STEP 10 : Unplug the black cable plugged into the rear of the radio. Unplug the plastic wire harness connector from the rear of the radio. The radio can now be pulled from the dash.
Read more »
Posted by at
Labels: , , , , , ,

BMW LCD COMMUNICATIONS INSTALLATION MANUAL


BMW LCD COMMUNICATIONS-INSTALLATION GUIDE

When you have set up a permanent location for the source of the alarm control unit and battery, as defined in the door switch to the vehicle type, you must specify the source is CONNECTED to a 12 volt power. This source is generally found on the flow switch wire harness and shows constant voltage, when the key is in the "on" and with the engine running. This voltage source must be removed, when the engine and ignition "OFF". When you configure a switched 12 volt source, look for parking the vehicle and leaving the lights on the wire. This wire is usually used for the light switch to the back or some handy light is installed in the vehicle, which is easily under the hood in front of the hotel. The correct wire displays voltage, when the light switch is turned on the lights in the parking place. If this installation instead of a siren, the vehicles Horn to honk the Horn line fuse block or Search the main harness fuse block.


VEHICLES, IT IS RECOMMENDED THAT YOU TAKE ADVANTAGE OF THE HIGHLY TECHNICAL NATURE OF THE VOLTMETER TO CHECK ALL ELECTRICAL CIRCUITS, OR FOR MAKING CONNECTIONS TO THE VEHICLE INSTEAD OF COMMON TEST LIGHT! Test the lights can cause damage to the vehicles computer if the wrong wires are asked and can result in air-bag systems to activate (use). Either the above cause extensive damage to the vehicle, which reads. Pay attention to all Warning labels on the vehicle. Automatic page creation assumes any liability to the account holder in this or any other vehicle or personal injury caused by improper installation damages. Professional installation is recommended for RF-520-security system. For details, see the limited lifetime warranty.


Download here

Read more »
Posted by at
Labels: , , , ,
Subscribe to: Posts (Atom)